16 Best Waterway Spa Pumps in 2018

 

Waterway Plastics 3722021-1d Executive 56 Frame 5 Hp Spa Pump, 230-volt - Viton shaft seals. 220 gallons per minute flow rate. Highly versatile wet end can be rotated every 90 degrees. 56-frame motor for added strength, cooler operating temperature and longer motor life.

 

Waterway 3722021-1d 2speed 5hp 230v Spa/hot Tub Pump - Large 6 1/2″ diameter wet end for higher head pressure. 56 frame motor for added strength, cooler operating temperature and longer motor life. Executive wet end designed specifically for 56 frame motors. Two double shielded ball bearings with moisture resistant grease for quieter operation and longer life. Highly versatile wet end can be rotated every 90 degrees.

 

Waterway 311-1210 Executive Pool And Spa Pump Faceplate, 2.5 In. - This is a faceplate used on the waterway mustang and executive pumps.

 

Waterway Plastics 3420610-15 48-frame Spa Pump - Executive wet end designed specifically for 48-frame motors. Large 6 &frac12 in diameter wet end for higher head pressure. Thermally protected to extend life expectancy of motor. Highly versatile wet end can be rotated every 90°. Large 2 &frac12 in intake for improved flow performance and reduced noise.

 

Waterway 3410020-1e 0.125hp 230v Single Speed Spa Pump - Side discharge for optimum flow. 230 volts. 24 hour circulation pump. Delivers 40 gallons per minute. 48 frame proven design.

 

3 hp 230V 2-Speed Waterway Spa Pump Side Discharge | 48 Frame Executive | 3421221-1A - If your heater is directly coupled to the spa wet end, then our pump will probably not work as the union will most likely be different. This will most likely involve cutting off your old unions and installing the new ones shipped with the spa pump. 2″ plumbing means you have 2″ schedule 40 pvc supply lines (2″ i. 2″ inlet & outlet measures 3″ o. The connection diagram for the new pump is located on the motor name plate. 2 3/8″ od on the line) circumference = 8″ (wrap a tape measure around the pipe). The various brands have their own unique style, which means you must use the unions provided with our spa pump. The pump does not come with a power cord. Ships with 2″ unions. Be sure to look at the motor voltage, not the voltage supplied to the spa to determine the correct pump voltage. Please read there is no industry standard for unions. Not self priming-water must be above pump head in order to operate properly. Simply just use the high speed connection. If you only require a one speed pump, this pump will work fine. When removing power cord from existing pump we recommend you mark your wires for “common”, “high speed”, “low speed”. If you are unsure if this pump will work for you, please call us, we can help assist you in your selection. D. The wet ends can be rotated by simply loosening the motor thru bolts and turning the pump head. D. The pvc pipe slides into the union and is glued with pvc cement. On the threads. It has nothing to do with the size of the union nuts, the size of the threads on the wet end or the inside diamater of the inlet/outlet. 2″ refers to the size of your pvc plumbing supply lines.

 

Waterway Plastics 3420620-15 1.5 hp 230V 2-Speed Spa Pump 1 2″ Center Discharge - 1. Not self priming-water must be above pump head in order to operate properly. If you are unsure if this pump will work for you, please call us, we can help assist you in your selection. 1 7/8″ o. D. 5″ i. The pump does not come with a power cord. When removing power cord from existing pump we recommend you mark your wires for “common”, “high speed”, “low speed”. 1. 5″ refers to the size of your pvc plumbing supply lines. If your heater is directly coupled to the spa wet end, then our pump will probably not work as the union will most likely be different. D. Please read there is no industry standard for unions. Be sure to look at the motor voltage, not the voltage supplied to the spa to determine the correct pump voltage. It has nothing to do with the size of the union nuts, the size of the threads on the wet end or the inside diameter of the inlet/outlet. If you only require a one speed pump, this pump will work fine. The various brands have their own unique style, which means you must use the unions provided with our spa pump. 5″ plumbing means you have 1. 5″ schedule 40 pvc supply lines (1. This will most likely involve cutting off your old unions & installing the new ones (400-4060) shipped with the spa pump. The wet ends can be rotated by simply loosening the motor thru bolts & turning the pump head, allowing the discharge to pt. The connection diagram for the new pump is located on the motor name plate. Optional debris basket 310-5400 available. 5″ (wrap a tape measure around the pipe). To 3 o’clock, 9 o’clock or 6 o’clock. Simply just use the high speed connection. On the line) circumference = 6. The pvc pipe slides into the union & is glued with pvc cement.

 

Waterway 310-4010 Gray Impeller Replacement For Waterway Hi-flo Discharge Series 1.5-horsepower Pool And Spa Pump - Available in gray color. Impeller replacement. Fits waterway hi-flo discharge series 15-horsepower pool and spa pump. This has an extended inlet opening and at the shaft side. Measures 3-2/3-inch length by 4/5-inch width size.

 

1.5 Hp 115v 2-speed Waterway Spa Pump 1 1/2" Center Discharge | 3420610-15 - Wetend can be rotated for easy installation. Reliable center discharge performance, 15″ inlet/outlet. 1 year manufacture warranty. 15 hp 3450/1725 rpm, 2-speed, 164/44 amps, 115v 60 hz. Overall length = 16″ height 735″ automatic overload protection.

 

Waterway 310-1500 Executive 3hp 230v 56y Frame Wet End Spa Pump - 56y frame thru bolt. Used with 3 horsepower motors.

 

Waterway 2 Speed 2.0 Hp 230v Spa Pump 3420820-15 - 3420820-15.

 

Waterway 400-4030b 1-1/2-inch Slip By 1-1/2-inch Mpt Union Assembly Replacement For Waterway Pool And Spa Pump - Measures 1-1/2-inch slip by 1-1/2-inch mpt. Fits waterway pool and spa pump. Union assembly replacement.

 

Waterway Plastics 3420410-1A 1 hp 115V 2-Speed Spa Pump 2″ x 2″ 48 Frame Executive Side Discharge - 5″ i. It has nothing to do with the size of the union nuts, the size of the threads on the wet end or the inside diameter of the inlet/outlet. The various brands have their own unique style, which means you must use the unions provided with our spa pump. 2″ inlet & outlet measures 3″ o. D. When removing power cord from existing pump we recommend you mark your wires for “common”, “high speed”, “low speed”. The pvc pipe slides into the union & is glued with pvc cement. The connection diagram for the new pump is located on the motor name plate. The wet ends can be rotated by simply loosening the motor thru bolts & turning the pump head. 5″ refers to the size of your pvc plumbing supply lines. 5″ plumbing means you have 1. If you are unsure if this pump will work for you, please call us, we can help assist you in your selection. If your heater is directly coupled to the spa wet end, then our pump will probably not work as the union will most likely be different. 1. The pump does not come with a power cord. Please read there is no industry standard for unions. 1 7/8″ od on the line) circumference = 6″ (wrap a tape measure around the pipe). 5″ unions. Be sure to look at the motor voltage, not the voltage supplied to the spa to determine the correct pump voltage. D. If you only require a one speed pump, this pump will work fine. 1. 5″ schedule 40 pvc supply lines (1. This will most likely involve cutting off your old unions & installing the new ones shipped with the spa pump. Simply just use the high speed connection. On the threads. Ships with 1. Not self priming-water must be above pump head in order to operate properly.

 

Waterway Ex2 Spa Pump Seal & O’ring Kit - Quality tork replacement parts. Fits both 48-frame & 56-frame motors. Kit includes #8, #7, #2 , (2) coupler orings, and lube pack. Waterway ex2 spa pump seal & o’ring kit.

 

Waterway Plastics 3411621-1A 4 hp 230V 1-Speed 2″ x 2″ 48 Frame Executive Spa Pump Side Discharge - 2″ refers to the size of your pvc plumbing supply lines. The pump does not come with a power cord. This will most likely involve cutting off your old unions & installing the new ones shipped with the spa pump. 2″ inlet & outlet measures 3″ o. D. It has nothing to do with the size of the union nuts, the size of the threads on the wet end or the inside diameter of the inlet/outlet. Simply just use the high speed connection. Be sure to look at the motor voltage, not the voltage supplied to the spa to determine the correct pump voltage. Please read there is no industry standard for unions. If you are unsure if this pump will work for you, please call us, we can help assist you in your selection. The pvc pipe slides into the union & is glued with pvc cement. The connection diagram for the new pump is located on the motor name plate. 2 3/8″ od on the line) circumference = 8″ (wrap a tape measure around the pipe). Not self priming-water must be above pump head in order to operate properly. If your heater is directly coupled to the spa wet end, then our pump will probably not work as the union will most likely be different. D. When removing power cord from existing pump we recommend you mark your wires for “common”, “high speed”, “low speed”. The wet ends can be rotated by simply loosening the motor thru bolts & turning the pump head. If you only require a one speed pump, this pump will work fine. On the threads. Ships with 2″ unions. The various brands have their own unique style, which means you must use the unions provided with our spa pump. 2″ plumbing means you have 2″ schedule 40 pvc supply lines (2″ i. .

 

Waterway 1 Speed 0.125 Hp 115v Spa Pump 3410030-1e - 3410030-1e.